WMF 8100 Bedienungsanleitung PDF herunterladen

CONGRATULATIONS!

Your new Remote Signal Activator (RSA) will now allow

you to use the TORTOISE™ to drive any scale crossing

gate or semaphore-style signal that has a vertical

actuating wire extending through the layout base. The

actuator features positive, screw-adjusted stops at both

the vertical and horizontal positions. Stops at the mid-

position for 3-color semaphore arms can be easily

accomplished by utilizing a CIRCUITRON SD-2 (800-

5520) Semaphore Driver Circuit. By purchasing an

extra RSA Cable and Actuator (part no. 800-8101), one

TORTOISE™ can simultaneously drive two gates at one

crossing.

HOW IT WORKS

The TORTOISE™ mounts to the drive mechanism and

can be located up to 18” from the signal. A drive arm

with multiple pivot holes (for adjusting the total throw)

moves a slide back and forth as the TORTOISE™ runs

(crawls?). A fine stainless steel wire is clamped to the

slide and moves inside a small teflon™ tube, much like

a sub-miniature choke cable. At the other end of the

wire and tube, an actuator bellcrank is swung by the

moving wire. Multiple holes are provided in the

bellcrank to

accomodate virtually

any vertically actuated

signal wire.

Fully adjustable screw

stops are provided to

set the range of

motion precisely. The

drive mechanism

assembly with the

TORTOISE™

mounted on it can be

located in any position

above or below the

layout surface. It may

even be possible to

locate the mechanism

inside of larger struc-

tures if that would be

an advantage.

CONTENTS

Please check your kit carefully and refer to the drawings to

identify all parts. You should have:

(1) Drive Mechanism Base Plate

(1) TORTOISE™ Mounting Plate

(1) Drive Mechanism Arm

(1) Slide

(1) Slide Clamp Plate (4 Shallow Grooves)

(1) Base Clamp Plate (4 Deep Grooves)

(1) Bellcrank Mounting Plate

(1) Actuator Clamp Plate (2 Deep Grooves)

(1) Bellcrank

(14) #4 x 3/8” Phillips Truss (large) Head Screws

(6) #4 x 5/8” Phillips Pan Head Screws

(2) #4 x 1/2” Phillips Shoulder Screw

(1) 18” Length Stainless Steel Wire

(1) 18” Length Teflon Tube

CAUTION: Handle the Stainless Steel Wire and Teflon

Tube carefully to avoid kinking either of them. Kinks will

degrade performance and may render the mechanism

unusable. Replacement Wire/Tube sets are available from

Circuitron for $3.00 postpaid.

TOOLS REQUIRED

#1 Phillips Screwdriver

Diagonal Wire Cutters (Hardened or Heavy Duty)

Flush Cutting Nippers

Needle Files

Square Jawed Needle Nose Pliers

Abrasive Cutoff Disc in Motor Tool

Drill with 3/32” drill bit.

Hobby Knife with new (sharp) #11 Blade

ACC Adhesive (Thin)

PREPARING THE PARTS

Remove all parts from their sprues, if necessary, and trim

the gate vestiges with flush cutters. File the trimmed

surface smooth on the Slide.

GETTING STARTED

1) Determine the total travel of the signal you want to

actuate by holding a caliper, ruler or scale next to the wire

under the layout and moving it between both extremes.

Refer to the chart in the next column and make a note of

the recommended pivot hole and Bellcrank hole to use for

your application.

NOTE: The numbers in the chart are just suggestions and

should provide a small amount of desirable over-travel for

most applications. However, the length of cable and

friction of the actuated device may affect the operation and

you may need to choose a hole combination that provides

somewhat more total travel.

Remote Signal Activator

[ GATE / SEMAPHORE ACTUATOR ]

800-8100

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Remote Signal Activator

CONGRATULATIONS! Your new Remote Signal Activator (RSA) will now allow you to use the TORTOISE™ to drive any scale crossing gate or semaphore-style si

Seite 2 - Fig. 2 Actuator

2) Place the Bellcrank over the molded boss on the Bellcrank Mounting Plate as shown above. Note that the 7 small tapered holes (Numbered 1 - 7 cou

Seite 3 - CAUTION:

5) Holding the wire with pliers, bend it to 90 degrees at the mark. 6) Drill two 3/32” pilot holes at the locations you marked in Step 4 and tempo

Seite 4

holes indicated. 22) Slip the mounting flanges on the TORTOISE™ Mounting Plate under the two screw heads. The smooth side of the Plate faces AWAY

Kommentare zu diesen Handbüchern

Keine Kommentare

WMF 8100 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Kaffeemacher WMF 8100 herunter. 8100 with WMF-INS.PUB Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kaffeemacher WMF 8100